Nycote 7-11 Tinted

Apply Nycote® 7-11 Tinted to metal surfaces that need protection from corrosive elements. It can be tinted an array of colors in order to assist the identification of parts that have been treated and to improve appearances. The liquid formula can be easily applied by painting, spraying or dipping areas that need protection from aircraft fuels, oil, lubricants, phosphate ester hydraulic fluids, salt spray and water. Contact factory for custom tinting.

Nycote® 7-11 Tinted also provides excellent high impact, abrasion resistance, flexibility and toughness at temperatures of -70°F to +300°F (-57°C to +149°C). Nycote® 7-11 Tinted has a six-month shelf life and the container can be resealed throughout. NSN: 8010-01-134-0415


Application Instructions

  • Carefully clean the surface of oils, grease and dust by using Nycote® Thinner Type I followed by NycleanTM for maximum Nycote® adhesion.
  • Shake container before using.
  • Apply Nycote® resin by brush, dip, fill and drain, or spraying techniques.
  • Allow one to two hours to achieve tack free surface before applying second coat.
  • When spraying we recommend using Nycote® Thinner Type II at a 25% to 50% volume ratio in order to reduce cobwebbing. Use low air pressure 10-20 p.s.i.
  • Allow wetted surface to air dry in dust and lint free area.
  • Follow cure timetable for full cure of film.
  • Cleanse equipment with Nycote® Thinner Type I.


Cure Timetable

Allow one to two hours to become tack free. In dry air allow 72 hours at room temperature for full cure or:

Heat 12 hours @ 120°F (49°C)
Heat eight hours @ 150°F (66°C)
Heat four hours @ 180°F (82°C)
Heat two hours @ 220°F (105°C)
Cure film temperature range is -70°F to +300°F (-57°C to 149°C)


Storage Temperature Requirements

Store at 70°F (21°C). Keep away from fire or flame.

Note: Ideal storage temperature is 70°F (21°C); acceptable storage range is between 65°F to 80°F (18.3°C to 26.7°C). Storing below 65°F (18.3°C) may cause cloudiness or gel; heat at 180°F (82°C) for two hours. This should restore the product to its normal liquid condition. If possible, re-verify viscosity with Zahn #2 cup (50-90 seconds).

Nycote® 7-11 Tinted has a six-month shelf life. The container can be opened, applied and then re-sealed for a period of six months. The storage temperature should be maintained for the entire shelf life period. The container must always be stored in an upright position. If the storage temperature is not the ideal, nor within the acceptable range, the result may change the nature of the Nycote® product, as well as, causing cloudiness of the liquid. At all times, the product should be kept from freezing.

>> Refer to SDS for all safety information

Nycote 7-11 Tinted Specifications

Physical Properties: Temperature Range from -70°F to +300°F (-57°C to 149°C)

Physical Properties Resin Film
Viscosity: @ 72ºF Zahn #2 Cup 50-90 Seconds n/a
Solids Content (non-vol.) 19% n/a
Flash Point: C.O.C 70°F n/a
Pounds Per Gallon @ 78°F            7.4±0.2 lb. n/a
Shelf Life @75°F 6 Months n/a
Film Thickness, 1 Dipcoat n/a 0.5 mil
Coverage Per Gallon 300 sq. ft. n/a
Tack-Free Time, 50% RH @ 70°F n/a 1 Hour
Film Pencil Hardness n/a 1-H
Adhesion ASTM D4541-09 (pull-off stress) n/a 1200 p.s.i. at temperatures of -70°F to +300°F (-57°C to +149°C). 
Abrasion Resistance - (500 Gr. #17 wheel 100 cycles) n/a 3.0 mgm

 

Resistance to Fluids: Excellent results in all areas tested

Fluid Resistance - 30 days immersion @ 75°F
JP-4
JP-5
JP-10
Kerosene
Gasoline
Skydrol®
100% RH @120°F
Distilled Water
Tap Water
Salt Spray
80% JP-4 Bacteria Laden Distilled Water

 

Adhesion Characteristics: Excellent results in all areas tested

Adhesion Characteristics
Untreated Aluminum
Chem-filmed (Irridited) Aluminum
Anodized Aluminum
Stainless Steel
Fiberglass
Zinc Chromate Primed Aluminum
Any Metal Surface
Adhesion SAE-AMS-S-4383 and MCS9001C




Contact our sales department for further information and pricing +1 (818) 764-9498 | [email protected].


Nycote® Laboratories is an ISO 9001:2008 and AS9100C certified company.